![]() ![]() You cannot drag your kayak over anything while the transducer is in place. There is slight drag and on rivers there is dangers of hitting rocks.īecause the PVC pipe is inserted from the bottom, if you want to remove it you have to get out and turn the kayak over. If you make your own it can be a bit time consuming to get it right. The transducer is placed in the kayak from the bottom. The transducer is mounted on a length of PVC plastic pipe the size of the scupper hole. This is another popular way of mounting a transducer. Through the Scupper Hole Transducer Mount It can get in the way when fishing on weedy or brushy lakes. You will have a lot of corrections strokes and the drag will slow you down. The problem is that you have a lot of drag on that side of the kayak. ![]() The transducer is mounted on PVC and can be mounted so the transducer is in the water off the side of the kayak. Over the Side of the Kayak Transducer Mount. If you have bubbles it can be some work to get the glue off and try again. You won't know if it works until it is dry. ![]() ![]() Pray the tape doesn't fail before it has time to set. You will then have to tape the transducer down firmly until the glue hardens. You still need to make sure there are no air bubbles which is hard to do when working with a tube of glue. You simply put marine glue on the kayak hull where you want the transducer to go. Gluing the transducer directly to the kayak using marine glue. But this will give you an idea of what is out there and any potential problems that exist. I am sure that some people have figured out ways around the problems and are using one of these methods just fine. Some work well but come with their own set of problems. Problems with Other Methods of Mounting the TransducerĪre a number of ways kayakers have mounted fish finder transducers. I then tried the above method and it has worked flawlessly. Years ago I actually tried the water method first and it didn't work at all. There is no need to add water inside the trough made when you curled the edges around the transducer.You can curl the edges of the putty to add a little protection to the transducer if you like. Press the transducer into the putty firmly.It should be flat on top where the transducer is to be placed. Press firmly to ensure every square inch is against the kayak hull. Put the putty where you want the transducer to go.If air bubbles are in the putty it will hinder the transducer and your fish finder will not work or you will get poor results at best. Important: This method using putty works because there is absolutely no air between the transducer and the kayak hull.Taken straight from the package you will probably not get any bubbles at all if you are careful. The Duct Seal doesn't come with any bubbles and is shrink wrapped at the factory. Squeeze and kneed it as much as needed if you see any bubbles. Make sure you work the patty to ensure there are no air bubbles.If you have a "V" shaped bottom you can make it a bit thicker. Get a 1/2 pound sized piece of putty and form "hamburger patty" an inch or so wider than the transducer.It can still be mounted right in the "V" using this method so the sonar is shooting down and not at an angle. The transducer should be shooting straight down so even if your kayak has a slight "V" bottom that is ok. Determine where you want the transducer to be mounted.Make sure all your fish finder cables are hooked up correctly. In most sit on top fishing kayaks, the fish finder will mount up front in front of the top hatch. Make sure you know exactly where your fish finder will be mounted and where the wires will be.Here is a step by step description of using putty to mount your transducer inside your kayak. Transducer is inside the kayak (see top photo) and always safe against damage.Transducer sticks firmly in the putty and will not fall out even when upside down.Will not harm polyethylene, the material most kayaks are made of.Is slightly sticky and will stick firmly to most materials.It can stay soft, pliable and workable for years.Here are just a few of the characteristics. Using this putty is the best I have found. I get a lot of questions asking the best way to mount the transducer. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |